[amsat-bb] RES: IC-9100 SatPC32 Sub Audible Tone for SO-50

[Rick Kowalewski]

Hi All,

Yes, the 2 lines for SO-50 as below are correct.

SO-50,67.0,$3F,1
SO-50,74.4,$3E,3

As per the SubTone.SQF file:

; SO-50: Before this satellite can be worked it has to be opened by a 
74.4 Hertz
; "burst" tone. Therefore the file contains an additional line with  
data for
; this tone frequency.  To set this tone frequency with SatPC32 click 
the "T"
; control until it shows  "T2". Then switch to TX for a few seconds. Click
; the "T" again until it shows "T1". That will set the tone frequency 
back to
; 67.0 Hertz.

73
Rick VK6XLR

On 1/07/2015 21:04, PY5LF wrote:
> Hi friends
> This set are working nice in my IC9100;
> SO-50,67.0,$3F,1
> SO-50,74.4,$3E,3
> I hope it works for you .
> 73
>
> PY5LF
> Luciano Fabricio
> Curitiba-PR-BR GG54jm
> http://www.qrz.com/db/PY5LF
>
> -----Mensagem original-----
> De: AMSAT-BB [mailto:amsat-bb-bounces at amsat.org] Em nome de Erich Eichmann
> Enviada em: quarta-feira, 1 de julho de 2015 09:44
> Para: Frank Westphal; AMSAT-BB at amsat.org
> Assunto: Re: [amsat-bb] IC-9100 SatPC32 Sub Audible Tone for SO-50
>
> Hi Frank,
> the program should come with the correct data for IC-9100 for the sub tone
> frequencies for 67.0 and 74.4 Hz. Unfortunately I don't have an
> IC-9100 (I loaned one from Icom when I added the functions to the program).
> So, presently I can't test the function myself.
>
> The sub tone frequency must be set on the Sub VFO because it is the TX VFO
> in Satellite mode. When you check the tone frequency the radio displays the
> tone frequency  of the Main VFO (if I remember correctly).
> So, did you first swap the VFOs before you checked the tone frequency and
> whether ist changes to 74.4 with T2?
>
> 73s, Erich, DK1TB
>
> Am 01.07.2015 um 07:47 schrieb Frank Westphal:
>> I have acquired an ICOM IC-9100 and am stumped on how to program
>> SatPC32 to select the correct sub audible tone for SO-50.  I have
>> studied the SubToneSQF file and the ICOM manual.  When I click on T0
>> and change it to T1 or T2 in SatPC32 the sub audible tone is turned on
>> in the IC-9100.  The tone frequency in the IC-9100 does NOT change to
>> the value in the SubToneSQF file.
>>
>> Has anyone figured out haw to correctly setup SatPC32 SubToneSQF file
>> to work with the IC-9100?  Could you post the correct command line so
>> I could copy it into my file?
>>
>> Thanks in advance for any guidance.
>>
>> Frank
>> K6FW
>>
>> _______________________________________________
>> Sent via AMSAT-BB at amsat.org. AMSAT-NA makes this open forum available
>> to all interested persons worldwide without requiring membership.
>> Opinions expressed
>> are solely those of the author, and do not reflect the official views
>> of AMSAT-NA.
>> Not an AMSAT-NA member? Join now to support the amateur satellite
>> program!
>> Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
>>
> _______________________________________________
> Sent via AMSAT-BB at amsat.org. AMSAT-NA makes this open forum available to all
> interested persons worldwide without requiring membership. Opinions
> expressed are solely those of the author, and do not reflect the official
> views of AMSAT-NA.
> Not an AMSAT-NA member? Join now to support the amateur satellite program!
> Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
>
> _______________________________________________
> Sent via AMSAT-BB at amsat.org. AMSAT-NA makes this open forum available
> to all interested persons worldwide without requiring membership. Opinions expressed
> are solely those of the author, and do not reflect the official views of AMSAT-NA.
> Not an AMSAT-NA member? Join now to support the amateur satellite program!
> Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
>