[amsat-bb] JY1SAT Sat Warehouse

[Hasan al-Basri]

Got it.
Hasan


On Fri, Nov 16, 2018 at 11:46 AM Graham Shirville <graham at shirville.com>
wrote:

> Just rushing for plane but yes either way will work ok but iif you want
> to display the tlm from each then you need to run the three dashboards..
>
>
> thanks
>
> Graham
>
>
> On 16/11/2018 17:17, planophore at aei.ca wrote:
> > Ok, just so that I am clear - I can run one dashboard (i.e funcube
> > dashboard) and it will decode FunCube, NAYIF-1 and JY1SAT telemetry
> > correctly identifying the source satellite and send that data to the
> > warehouse and the correct telemetry for the correct satellite get put in
> > the right place?
> >
> > I have just started playing around with decoding FunCube and NAYIF
> > telemtry, and lookin forward to JY1SAT and have been trying to devise a
> > plan on how to do all three at the same time.
> >
> > I was going to run one instance of each of the dashboards and schedule a
> > receiver to change frequencies for a specific satellite when in view but
> > it sounds like I can just one dashboard and feed it with my one receiver
> > with it's scheduled frequency changes.
> >
> > Is that correct?
> >
> > cheers, Graham ve3gtc FN25 near Ottawa Canada
> >
> >
> >
> > On 11/16/2018, "Hasan al-Basri" <hbasri.schiers6 at gmail.com> wrote:
> >
> >> Graham,
> >> I can't thank you enough. I now have 3 dashboards installed, FC-1,
> Nayaf-1
> >> and JY1-Sat. I can run all at the same time, and I can also run 3
> receivers
> >> at a time, all feeding their audio streams to the software (SDRs are
> soooo
> >> nice)
> >>
> >> Awaiting my 1st nayaf-1 tlme pass (3 min AOS). Signals were quite strong
> >> earlier, but I didn't have the right decoder software up yet.
> >>
> >> Thanks again.
> >> 73, N0AN
> >> Hasan
> >>
> >>
> >> On Fri, Nov 16, 2018 at 10:27 AM Graham Shirville <graham at shirville.com
> >
> >> wrote:
> >>
> >>> Hi Hasan,
> >>>
> >>> Yes you site id authentication can be the same for all dashboards,
> >>> currently FC1 and Nayif. You can also use the same id for the new ESEO
> >>> and JY1SAT dashboard from next week (hopefully).
> >>>
> >>> If you are running the FC1 dashboard and it receives and decodes data
> >>> from Nayif- it will send these to the Data Warehouse automatically. You
> >>> will see the bottom RH count going up beyond the LH number. Youcan,
> >>> usually run both dashbaords at the saem time if you wish to display
> >>> everything!
> >>>
> >>> 73
> >>>
> >>> Graham
> >>>
> >>>
> >>> On 16/11/2018 16:07, Hasan al-Basri wrote:
> >>>> I've been decoding and uploading AO-73 data with the Funcube-1
> Dashboard.
> >>>>
> >>>> I just downloaded and installed JY1-Sat Dashboard.
> >>>>
> >>>> IAre the Site ID (my call) and the Auth code the same for both upload
> >>> sites?
> >>>> I should have a pass of EO-88 in about 30 minutes. Is there any
> >>> indication
> >>>> from the software that my data is being accepted at the site, based on
> >>> the
> >>>> same ID and Auth as for AO-73 ?
> >>>>
> >>>> TIA,
> >>>> 73, N0AN
> >>>> Hasan
> >>>> _______________________________________________
> >>>> Sent via AMSAT-BB at amsat.org. AMSAT-NA makes this open forum available
> >>>> to all interested persons worldwide without requiring membership.
> >>> Opinions expressed
> >>>> are solely those of the author, and do not reflect the official views
> of
> >>> AMSAT-NA.
> >>>> Not an AMSAT-NA member? Join now to support the amateur satellite
> >>> program!
> >>>> Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
> >>>
> >> _______________________________________________
> >> Sent via AMSAT-BB at amsat.org. AMSAT-NA makes this open forum available
> >> to all interested persons worldwide without requiring membership.
> Opinions expressed
> >> are solely those of the author, and do not reflect the official views
> of AMSAT-NA.
> >> Not an AMSAT-NA member? Join now to support the amateur satellite
> program!
> >> Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
> >>
> >>
>
>