[amsat-bb] Satpc32 and ICOM 9700

[Stefan Wagener]

Please refer to:

https://www.amsat.org/wordpress/wp-content/uploads/2020/01/SatPC32-IC9700-Setup-1.pdf

73, Stefan VE4SW

On Sat, May 9, 2020 at 11:04 AM Jack Spitznagel via AMSAT-BB <
amsat-bb at amsat.org> wrote:

> Peter,
>
> I forgot two important adds about selecting the 9700 and the correct
> Baudrate which ARE described well:
> http://www.dk1tb.de/IC9700_settings.htm
>
> I use the USB settings and they work as advertised. Some folks say the
> C-IV setup works more reliably, but I have not seen a difference except
> that the USB speed is more lively.
>
> Not my best day to concentrate...
> Jack - KD4IZ
>
> -----Original Message-----
> From: AMSAT-BB <amsat-bb-bounces at amsat.org> On Behalf Of Jack Spitznagel
> via AMSAT-BB
> Sent: Saturday, May 9, 2020 10:57
> To: AMSAT-BB at amsat.org
> Subject: Re: [amsat-bb] Satpc32 and ICOM 9700
>
> Peter,
>
> I had the same problem until I looked back through the general
> documentation. Was not clear in the 9700 setup instructions.
>
> When you bring up the radio setup it comes up showing "Model" in the top
> pull down field next to "Radio 1". Select Icom radio button, then you need
> to click on that pull down field and select the third choice which is
> "Addresses" it should show "$A2   $A2" in the pull down field just below.
> If not, you can activate the pulldown and select the correct one or adjust
> each field using the "up/down" arrows beneath each address that is shown.
>
> Hope that makes sense.
>
> Jack Spitznagel – KD4IZ
> Trustee for NR3DT
> The Museum Ship USCGC Taney WHEC-37 Amateur Radio Group
>
> -----Original Message-----
> From: AMSAT-BB <amsat-bb-bounces at amsat.org> On Behalf Of Peter via
> AMSAT-BB
> Sent: Saturday, May 9, 2020 10:24
> To: amsat-bb at amsat.org
> Subject: [amsat-bb] Satpc32 and ICOM 9700
>
> I'm confused, the address for my radio is A2h but the choices inside
> Satpc32are nothing like that.  What am I missing?
> Also, how can you confirm the program and radio are communicating?  How
> can I force the program to do something to the radio and thus show me that
> they arein contact with one another?  I've turned on CAT and it goes plus
> without anerror but that's not enough THanksPeterW2PP
> _______________________________________________
> Sent via AMSAT-BB at amsat.org. AMSAT-NA makes this open forum available to
> all interested persons worldwide without requiring membership. Opinions
> expressed are solely those of the author, and do not reflect the official
> views of AMSAT-NA.
> Not an AMSAT-NA member? Join now to support the amateur satellite program!
> Subscription settings: https://www.amsat.org/mailman/listinfo/amsat-bb
>
> _______________________________________________
> Sent via AMSAT-BB at amsat.org. AMSAT-NA makes this open forum available to
> all interested persons worldwide without requiring membership. Opinions
> expressed are solely those of the author, and do not reflect the official
> views of AMSAT-NA.
> Not an AMSAT-NA member? Join now to support the amateur satellite program!
> Subscription settings: https://www.amsat.org/mailman/listinfo/amsat-bb
>
> _______________________________________________
> Sent via AMSAT-BB at amsat.org. AMSAT-NA makes this open forum available
> to all interested persons worldwide without requiring membership. Opinions
> expressed
> are solely those of the author, and do not reflect the official views of
> AMSAT-NA.
> Not an AMSAT-NA member? Join now to support the amateur satellite program!
> Subscription settings: https://www.amsat.org/mailman/listinfo/amsat-bb
>