[amsat-bb] JY1SAT Sat Warehouse

[planophore at aei.ca]

Ok, just so that I am clear - I can run one dashboard (i.e funcube
dashboard) and it will decode FunCube, NAYIF-1 and JY1SAT telemetry
correctly identifying the source satellite and send that data to the
warehouse and the correct telemetry for the correct satellite get put in
the right place?

I have just started playing around with decoding FunCube and NAYIF
telemtry, and lookin forward to JY1SAT and have been trying to devise a
plan on how to do all three at the same time.

I was going to run one instance of each of the dashboards and schedule a
receiver to change frequencies for a specific satellite when in view but
it sounds like I can just one dashboard and feed it with my one receiver
with it's scheduled frequency changes.

Is that correct?

cheers, Graham ve3gtc FN25 near Ottawa Canada



On 11/16/2018, "Hasan al-Basri" <hbasri.schiers6 at gmail.com> wrote:

>Graham,
>I can't thank you enough. I now have 3 dashboards installed, FC-1, Nayaf-1
>and JY1-Sat. I can run all at the same time, and I can also run 3 receivers
>at a time, all feeding their audio streams to the software (SDRs are soooo
>nice)
>
>Awaiting my 1st nayaf-1 tlme pass (3 min AOS). Signals were quite strong
>earlier, but I didn't have the right decoder software up yet.
>
>Thanks again.
>73, N0AN
>Hasan
>
>
>On Fri, Nov 16, 2018 at 10:27 AM Graham Shirville <graham at shirville.com>
>wrote:
>
>> Hi Hasan,
>>
>> Yes you site id authentication can be the same for all dashboards,
>> currently FC1 and Nayif. You can also use the same id for the new ESEO
>> and JY1SAT dashboard from next week (hopefully).
>>
>> If you are running the FC1 dashboard and it receives and decodes data
>> from Nayif- it will send these to the Data Warehouse automatically. You
>> will see the bottom RH count going up beyond the LH number. Youcan,
>> usually run both dashbaords at the saem time if you wish to display
>> everything!
>>
>> 73
>>
>> Graham
>>
>>
>> On 16/11/2018 16:07, Hasan al-Basri wrote:
>> > I've been decoding and uploading AO-73 data with the Funcube-1 Dashboard.
>> >
>> > I just downloaded and installed JY1-Sat Dashboard.
>> >
>> > IAre the Site ID (my call) and the Auth code the same for both upload
>> sites?
>> >
>> > I should have a pass of EO-88 in about 30 minutes. Is there any
>> indication
>> > from the software that my data is being accepted at the site, based on
>> the
>> > same ID and Auth as for AO-73 ?
>> >
>> > TIA,
>> > 73, N0AN
>> > Hasan
>> > _______________________________________________
>> > Sent via AMSAT-BB at amsat.org. AMSAT-NA makes this open forum available
>> > to all interested persons worldwide without requiring membership.
>> Opinions expressed
>> > are solely those of the author, and do not reflect the official views of
>> AMSAT-NA.
>> > Not an AMSAT-NA member? Join now to support the amateur satellite
>> program!
>> > Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
>>
>>
>_______________________________________________
>Sent via AMSAT-BB at amsat.org. AMSAT-NA makes this open forum available
>to all interested persons worldwide without requiring membership. Opinions expressed
>are solely those of the author, and do not reflect the official views of AMSAT-NA.
>Not an AMSAT-NA member? Join now to support the amateur satellite program!
>Subscription settings: http://www.amsat.org/mailman/listinfo/amsat-bb
>
>